Known GOOD Service Facilities

For a time there has been a lack of good service facilities for the repair of tape decks but in time some of them have come out of the woodwork to make themselves know. This is a list of the ones I know do good work.

Not everyone is perfect and I even get complaints due to wait time.  But on a whole these places  99% of the time will fix your unit well.

In The Pacific Northwest: Curt Palme       http://reeltoreeltech.com/    Email: info@reeltoreeltech.com  604-514-1751

Sound Solutions Inc                                                                                   #344-19567 Fraser Hwy                                                                                  Surrey BC  V3S9A4


New Jersey Factory Service, Inc.
16 Chestnut Avenue Suite 103 B
Emerson,New Jersey 07630
201-967-0060
Mon- Wed 8-4   Thurs 8-2 Closed Fri  Sat/Sun by appt.
www.njfactoryservice.com    Analog/Digital Audio Repair


Tom Brucker

Hi Tech Service
2934 Nolensville Pk.
Nashville, TN 37211
615-331-9241


Crown repairs ,Chuck Ziska   Ocala,Fl.  352-861-1052   ocalazman@embarqmail.com

——————————————————————————-

In Florida we have a new high level Technician-

Vintage Stereo Repair and Restoration
Repairing and restoring analog audio components
Teac, NAD, dbx, Revox, B&O, Pioneer
Gerhard@TheVintageAudio.com
772-713-1506


For those in Italy-

Giovambattista Currado
mob. +39 3334463179
currado@email.it
www.facebook.com/GBCLab
www.revoxa77.com

Need a Good SM avoid Hi Fi Engine

I have been working on units a log time and some of the time I get requests for help that I do not have manuals for so over to Hi Fi Engine I went. Most of the time  I was able to help the other guy for no cost. Well most recently I was working on a  Sony 854-4 where I got the manual from Hi Fi Engine. The schematic is so bad that you can not see what the part numbers are- what idiot scans stuff like this and what further idiot puts in on a site for some poor person to download and try to work with.

Well I made a comment to them about the poor quality and now I am done with their poor scans and idiotic behavior. Why don’t they come up to standards rather then kick people out from downloading their garbage.

No matter, I am not going there anymore and do not suggest to anyone that you do either. If I can not fix a product with all my experience and their blurry manuals what makes you think that a person just starting is going to be able to.

Get all you manuals in paper from Stereomanuals.com

This place will get you a good and clear product.  http://www.stereomanuals.com/index.htm

Hi FI Engine Quality-JUNK!

Anybody Want a Web Blog like this one? Look at this-

I keep on getting comments on how people want a blog like the one here that I put up. Well, it is not that hard to do and it is very affordable. This link here will get you to the trial one month evaluation. Actually for the quality of the product they deliver and at a terrific price it is a no-brainer.

I highly suggest that you look into this and not pay some SEO person hundreds of dollars to make you a different site. You found me didn’t you?

https://www.1and1.com/1and1principles-hosting

Tell them I sent you (467419039)

Items Ready to be Sold with 6 Mo. Warranty

These items listed  here are ready to be sold. Not every one will be a Mint as these are older units and often times rescued from adverse locations. Many of them are very acceptable and the pictures here are of the actual units. More units will come available as they are finished.

This Teac A2000 was restored with all new Electrolytic capacitors, New belts, heads have very few hours on them. All motors oiled, calibrated for LPR35 tape in High bias setting. The speed is 3005Hz with wow and flutter in the .04% range as AMSoil was applied to bearings and motors. All pots and switches cleaned. It has a new motor run capacitor. The unit has some upper left damage of a corner to one panel. I did not have new one to put on at this point. Works very well at both speeds. 7.5 IPS is 50-20KHz inside of plus or minus 2dB at 0Vu relative to 200nWb/M flux density.

Asking $500. Other offers will be considered. skywavebe@sbcglobal.net

 

 

 

 

Teac X7R and other X7 models Fast Wind Speed Fix Modification

One of the most aggravating things is to fast wind a X7R and have to wait the 2.5 to 3 minutes to have it finish a 1800 foot roll of tape.  Ha! Teac knew there was a problem and  released technical bulletins to make some corrections. Well I use a different approach in application of the 30Vdc supply to the motors only in fast wind mode. Does this work you might say? Well both fast winds with my modification finished the same roll of tape at 58 seconds. I have taken a signal out of the logic that signals the reel motor drive that it is doing fast wind mode. This then goes through some resistors and transistors to invert the signal to drive a TIP107 transistor that then sends the higher voltage to the motors. There is a diode that maintains the 14Vdc supply at play mode on those motors and that prevents the feed of the 30 Vdc supply back to the 14Vdc supply. I have tested this deck and it is going through more tests but if you want to get your deck corrected for this problem, contact me.

Well the first of my mods is out there and only time will tell if the client likes it. I have a feeling that anyone who has sat through the slow wind speeds will fine this less than a minute speed much better. I have obtained some further parts to build these kits. I just have to do the  schematic and instructions. I think the idea will be well received once people find out how well these decks can work.

Damping Silicone in 8ml bottles

This product is used to dampen the movement of left tension arms in Teac and other tape decks. Its Viscosity is 300,000 cSt.  The 8mL sized bottle should be enough to do 3-5 tension arms per bottle. As you probably already know this product is not easy to find. The product name is Dimethyl Polysiloxane. I offer this as a service to my fellow Service Technicians who can not afford to buy a Gallon of it for over $400.

I have used it successfully on a number of decks already. It does work.

Cost is $8.00 plus $7.20 shipping.

Contact me at skywavebe@sbcglobal.net to order one or a couple bottles.

They are in limited numbers.Silicone 8ml-2

They are clear after the bubbles rise. Probably can service 10-20 machines from one bottle.

What you need to know for Repairs

Over the last 45 years of service in the Electronics Industry, I have worked on anything from Coffee Pots, Rice cookers, VCR’s, Camcorders, Digital Betacam, and then Transmitters in the AM and FM Radio business.  There is a lot to see. But in working on consumer tape decks and amplifiers there are a few things that stick out for anyone wishing to repair electronics should watch out for.

They can be things like poor wave soldering of the boards. There is so little solder on these parts that the smallest bump or vibration will cause a failure of that circuit. Multiply this by 100- 200 joints in a machine and you have a real good chance that it will need repair sooner rather than later. Other things that can break weak joints are conditions of thermal cycling. Does the part have a heat sink on it or does it get hot? Well so does the joint. So many cycles will make the solder joint weak and it was develop a ring around the part lead and again an intermittent connection or break. Corrections done by a good Technician who knows how to solder using Kester 44 (Lead) solder will do wonders for the longevity of the unit.

That is not the only thing that causes failure. There is the infamous 10 V Electrolytic capacitor. These 10 V types have proven a very high failure part so that I often tell others that I am allergic to 10 V caps. Many a tape deck or other equipment that have this part are on borrowed time from when they are made. I just was working on a Teac Z6000 tape deck. Playback was lost on the left channel. Further examination indicated that the coupling cap was defective and must have had a bad connection inside. What value was it? 220uFd/ 10V. Not the type of part I would expect in a $1500 tape deck. Don’t feel bad Teac, Revox and Uher have their Frako caps too. They are notorious for shorting.

7/18/16

OK, Now for the X series tape decks from Teac. Some think that having dual capstan drive is a plus. Technicians can tell you what a headache they can be. There is sensitivity to belt length, belt position, how clean the pinch rollers are and dirt on the capstan shaft. However, what causes me to write this is that I have also found the the two conditions that are seen are either Skew or tape looping. Looping is when the tape comes away from the heads making a perfect loop down below them. This is most likely caused by a loose belt. Most all X series need a 16.8″ belt but some sell 17″ belts that are near the limit to not use them. They sometimes do not work and if they do only for 6 month. Marrs has the good belts at 16.8″ X .330″ wide.

Next there is Skew. This is when the tape travels off the straight path at the pinch roller. I have determined recently that some genius adjusted the head position on the head block so that they are tilted and THIS make the tape skew. Of course the machine never works like they adjust them. Just go turning all the head screw and you are sure to make the deck better- Yes after about $160 of Technicians work. Rule is don’t touch these screws you need a lot to put them back into position.. Please,I have more than enough work already.

The best Service Manuals come from Stereomanuals.com .  If I do not have one I need that is where I get them!

In Canada, A new site for service in your area may be this one here. http://reeltoreeltech.com/

Give them a call and see if they can help you. Tel: 604-514-1751  Talk to Curt.     Email: info@reeltoreeltech.com

Tascam 122 Mk III and Other models- 112, 488 and so on: Gear C

I am now at the point that I am taking orders for the gear that so many service shops and people need to fix their blinking transport lights problem. Teac does not have this part any more but I have had them made up. They are $30 plus the postage- I will not ship in a flat envelope like the $80 guy does on E bay. What does it look like-This is a Resin cast gear as were the original ones. Some call it gear B some Gear C. In the 122 Mk III parts diagram 4 the 4-34 part is what this is and was part number 5801474300 and sub’d to 9278377600.

122Gear wm

To obtain one or some, contact me at skywavebe@sbcglobal.net . I take credit cards- MC, Amex, Visa and Discover and can take Paypal as well. The cost of obtaining the gears has gone up slightly so they are $30 each now. Also know that the mechanism must be cleaned and greased prior to use or the same problem can occur. I have never had a new one fail yet. I use Lubriplate 105 to lubricate the mechanism first. Also the contact plate.

Green arrow points to Gear C.

Every once in a while I get a guy who complains about the gear price. NO there are no $.33 gears nor $2.00 gears or you would not be contacting me. The gears cost the manufacture near $3000 to set up and make these custom made gears- he dictates the price he wants for them. There is conjecture that I make $20 profit on a gear and I can tell you that is not at all what they cost. There is a guy selling hundreds of gears on E bay who started at $80/gear. He sells them for $39 now. If you want to buy from him to save money then do so. There are a limited number of gears and when they run out that might be it. I use the same gears in repairs and there is no reason I HAVE to sell them. With enough of this aggravation I might not.

As of 1/27/2019 the postage has been increased to $7.90 for flat rate.

http://www.disclosureproject.org

Items For Sale

People have trouble buying good decks from E bay mostly because the equipment there is old and has had very little maintenance and some of it has been tampered with by amateurs. Well here is a place you can get a deck that has been checked out, calibrated and tested for correct function. They also have a 6 month warranty.

I will be offering Teac, Tascam, Nakamichi, Pioneer and other brands that have passed our testing procedure. There are units ready now I just have to get the pictures ready.

I have had units ready to sell but some of them sold before I could even take a picture of them to list here. It seems I can not get them ready fast enough.

Recently there was a repair that was done and the customer refused the unit so it is for sale here with a new capstan motor and belts plus all the alignment and calibration and a 6 month warranty. $185 The model is the DR-M14HX. Specs as measured can be sent to prospective buyers by E mail. Questions can be answered or further pictures sent as well.

THIS ITEM SOLD

630-616-0932 Office, skywavebe@sbcglobal.net  E mail.

=================================================

People who have walkmans of the WM-D6C type continue to ask me if I have an AC adapter for it. Well I did a little research and came up with a limited number of these that can take in 100Vac to 240Vac and put out 6Vdc with a negative center post. These are made for these Walkmans and I have tested them with WM-D6C units. They are going for $12 each and have a 1 year warranty. It also comes with a smaller adapter that can work with other walkmans provided they are 6Vdc and negative center. 6Vdc at 1Amp.

These are switch type adpaters- Postage around $7.20 Priority mail.

Local Service Shops?

I have been working on some machines that are clearly butchered by local shops. If I was to be doing this kind off work I would not put a big gold sticker on the back saying Electronic Sale and Service. The Service part is clearly not there. You have to be careful who you hand your equipment to and one of the first signs they are only after your money is the Deposit Fee.

Another thing I find annoying is that they don’t put all the screws back or that they put them in with a jack hammer and strip out the heads. Some machines that I get in show the only thing the guy who worked on it last was good at was putting a lot of wire ties on. Of course they all have to be cut out to correct his incompetent work. Just today I had a Audio board mounted wrong with tape and insulation foam added to the board. Why not save all this time and tape and put the board in the right way? They left the front pots not tightened down and then used a cassette deck belt in an open reel. It was real dirty inside but they did nothing about that. Maybe the dirt accumulated came from their shop where it sat for a long time. Of course it works well now. Teac’s lowest reel deck of the line an X-3 derivative called a 22-2 has a wow and flutter of .018% after I got done with it. Must be that AMS Signature oil I put in.

Recently I got a Pioneer RT909 in that had the belt changed in it and new Pinch Rollers put on. Yet the person at the shop completely skipped over the stuck Pinch Roller linkage and then when the 25 V zener diode shorted, he said he could not fix the deck. What kind of people operate shops like this- this one is in MO. I find it strange that they even take them in and charge for this kind of work- they are totally bogus I would say.